Adventure/Touring Bike Drive Chains

5-Speed Door Puller by JIMS®. Use to remove Big Twin 5-Speed transmission door. This tool easily removes the transmission door, with gears and shafts attached and without any scratches or frustrations. Puller will not damage door bearing.

6-Speed Main Drive Gear Bearing and Seal Installer Tool by JIMS®. Use this tool to safely install new main drive gear bearings and seal. This tool will hold bearings and seal square to it's bore, eliminating any marring of the bearings...

Balancer Scissor Gear Alignment Screw by JIMS®. This tool holds the two halves of the spring before removal for easy installation. No more fumbling with screwdrivers while trying to align the gear in place. This screw is brightly...

Bearing Installer by JIMS®. Designed to safely remove and install the inner primary bearing H-D® #9135 without any damage to the new bearing. This is done by pushing on the outer perimeter of the bearing. Also removes and installs...

Cam Bearing Puller by JIMS®. Once the camshafts are removed from the support plate this specialty tool will remove the bearing from the camshaft. Unlike a general purpose puller this tool was designed to remove the bearing straight with...

Cam Bearing Tool by JIMS®. Use to install inner cam bearing, with Handle No. 33416- 80 on right (Handle slips through the outer cam bushing for alignment). All of JIMS® bearing installers are designed with an angle to apply all the...

Cam Chain Tensioner Tool by JIMS®. This tool will unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams. This tool also checks spring loads on chain tensioners.

Clutch Assembly Service Tool by JIMS®. This tool will safely disassemble and assemble the clutch shell assembly. Easily removes and installs the clutch hub from it's bearing. Safely removes and installs the clutch shell ball bearing...

Clutch Hub Puller by JIMS®. Use to remove wet and dry clutch hub without removing clutch release rod. 4 bolts included for dry clutch removal. If you're looking for a quality product that will serve you for years to come, look no further.

Clutch Spring Compressor Adaptor by JIMS®. Thanks to Rob Curtis, JIMS now have an adapter for JIMS No.38515-90 clutch spring compressor that makes it possible to use this tool for a similar application on Victory® motorcycles. For...

Countershaft 1st Scissor Gear Alignment Tool by JIMS®. This tool is essential for installation of the countershaft 1st scissor gear in Milwaukee Eight™ / Cruise Drive transmissions. It is installed before the scissor gear is removed...

Cruise Drive Vise Stand by JIMS®. Faster, easier, and safer assembly is now possible. To assist in the assembly of the transmission gears and shafts, JIMS® has developed the Cruise Drive Vise Stand. No more fumbling with parts on the...

Universal Hardware Organizer Complete Kit by JIMS®. Tired of hunting through plastic bins looking for hardware? The patent pending JIMS Hardware Organizers will guarantee all hardware is organized during powertrain teardown, storage,...

Head Holder by JIMS®. Designed with a special guide alignment shaft that holds the right angle for the best possible installation. Save time andmoneyby installing the guides, in-line, with the valve seats, time and time again, for much...

Inner Primary Bearing and Seal Removal/Installation Kit by JIMS®. When it comes to servicing the inner primary bearing and seal, do it the JIMS way. This American made tool has a lifetime warranty and drives the bearing and seal...

Main Bearing Installer Tool by JIMS®. Use this tool to safely install a new main bearing using hand tools. This job can be performed with the transmission still in the frame. Tool will hold bearing square to it's bore, eliminating any...

Main Bearing Remover and Installer by JIMS®. The Milwaukee Eight™ engine uses a completely unique engine case main bearing. With this in mind, JIMS® is proud to introduce a main bearing remover and installer designed just for the...

Main Drive Gear Installer Tool by JIMS®. Use this tool to safely install a new or newly repaired main drive gear. This job can be performed with the transmission still in the frame, with hand tools. This tool will hold the main drive...

Main Drive Gear Remover Tool by JIMS®. This tool removes the main drive gear from the main bearing correctly while in the transmission case. This eliminates the need of an arbor press and the risk of case damage.

Main Drive Gear Tool by JIMS®. Use to remove and install the main drive gear. Also installs the main bearing without removing transmission case. If you're looking for a quality product that will serve you for years to come, look no...

Mainshaft Replacement Bearing Plate by JIMS®. Use to remove and install the bearing inner race on the transmission mainshaft. If you're looking for a quality product that will serve you for years to come, look no further.

Mainshaft Sprocket/Pulley Locknut Socket by JIMS®. Heavy-Duty thick wall tube. Extra long two piece design, inner collar will retain wrench to nut for safer service work. 1-7/8" hex, 1/2" Drive. If you're looking for a quality product...

Neck Bearing Tool by JIMS®. Including Tri Glide® trikes. A new frame design change in the steering head & neck bearings for Harley-Davidson® motorcycles necessitates a new installation tool. Pounding the races into place is simply not...

Primary Cover Inspection Plug Tool by JIMS®. This tool is used to remove and install the OEM style primary cover clutch adjuster access plug and filler plug without distorting the plug's slot. If you're looking for a quality product...

Primary Locking Bar by JIMS®. Use to lock primary for service work. This tool locks the primary drive on XL models to facilitate crankshaft sprocket nut removal and installation, along with clutch service. By shifting the transmission...

Primary Locking Bar by JIMS®. Use to lock primary for service work. Designed with precision and functionality in mind, this accessory ensures outstanding performance and easy use which makes it the perfect deal for your ultimate...

Shifter Mechanism Sleeve Remover and Installer Tool by JIMS®. This is a real time saver for removing and installing the shifter mechanism sleeve in Cruise Drive Big Twin transmissions. With this new tool, the sleeve (bushing) can be...

Sprocket Locker by JIMS®. Use to lock final drive sprocket, for removing and installing sprocket nut. Use with JIMS® tool No.94660-37A. If you're looking for a quality product that will serve you for years to come, look no further.

Steering Head Bearing Race Installer by JIMS®. Use to install steering head races, stock and custom, as well as install cups in the frame. This tool pulls the races and cups in, straight and true, without any damage.

Steering Head Bearing Race Remover Tool by JIMS®. Use to remove and install steering head bearing race. Use with JIMS® spacer No.2388 and JIMS® Tool Handle No.33416-80 below. If you're looking for a quality product that will serve you...