JIMS Motorcycle Drivetrain & Transmission Parts

Connecting Rod Bushing Tool by JIMS®. Use to remove and replace wrist pin bushings without removing connecting rods from crankcases. Use JIMS® No.1284 Rod Holder tool. If you're looking for a quality product that will serve you for...

Sprocket Shaft Bearing Installation Tool by JIMS®. Use to install flywheel assembly into left crankcase Timken® bearing. Designed with precision and functionality in mind, this accessory ensures outstanding performance and easy use...

6-Speed Main Drive Gear Bearing and Seal Installer Tool by JIMS®. Use this tool to safely install new main drive gear bearings and seal. This tool will hold bearings and seal square to it's bore, eliminating any marring of the bearings...

6-Speed Transmission Door Remover Tool by JIMS®. Use this tool to remove (pull) the complete door with gears and shafts from the transmission. No longer will you need to remove the trap door by prying or hitting with a hammer. Just...

Balancer Shaft Bearing Remover and Installer Tool by JIMS®. Performs like JIMS® other bearing removers by simplifying bearing removal. This tool will pull the bearings from the "B" motor case in one easy smooth motion preventing any...

Bearing and Race Puller Tool by JIMS®. This tool has been designed to remove the flywheel sprocket shaft inner bearing race with the supplied JIMS® T-bar and hardware. If heat is needed to remove race see tool No. 899.

Clevebloc Bushing Assembly Remover/Installer Tool by JIMS®. Use to remove and replace swing arm cleveblocs. Cleveblocs, part No.47556-81, are silicone filled bushings that will be damaged if not installed properly. JIMS® tool presses...

Clevebloc Spreading Tool by JIMS®. Use to install the swing arm in a 5-Speed rubber mount frame. When cleveblocs are replaced they need to be positioned to install in the rear of the transmission. This tool will spread the swing arm...

Clutch Hub Locking Tool by JIMS®. Use to lock the clutch hub assembly in place when removing or installing the clutch hub nut. Designed with precision and functionality in mind, this accessory ensures outstanding performance and easy...

Clutch Spring Compressor Tool Nut by JIMS®. Use to release clutch spring for ease of retainer ring removal and installation (Must be used with No.38515-90 Main Body). Available Separately. Designed with precision and functionality in...

Main Bearing Installer Tool by JIMS®. Use this tool to safely install a new main bearing using hand tools. This job can be performed with the transmission still in the frame. Tool will hold bearing square to it's bore, eliminating any...

Main Drive Gear Bearing Tool by JIMS®. Use to install inner and outer 5th gear bearings to factory depth. New bearing depth incorporated, will still work on early depth. If you're looking for a quality product that will serve you for...

Main Drive Gear Bushing Tool by JIMS®. Use to remove and install the main drive gear bushings, also to remove Big Twin cam bushing 1970- present. If you're looking for a quality product that will serve you for years to come, look no...

Mainshaft Replacement Bearing Plate by JIMS®. Use to remove and install the bearing inner race on the transmission mainshaft. If you're looking for a quality product that will serve you for years to come, look no further.

Universal Race and Bearing Install Tool Handle by JIMS®. This top-grade product is expertly made in compliance with stringent industry standards to offer a fusion of a well-balanced design and high level of craftsmanship. Manufactured...

Sprocket Shaft Bearing Installation Tool by JIMS®. Use to install flywheel assembly into left crankcase Timken® bearing. Designed with precision and functionality in mind, this accessory ensures outstanding performance and easy use...

Timken™ Bearing Or Race Installer Adapter Kit by JIMS®. This tool will upgrade your earlier JIMS® bearing installer tool to work on the latest fine spline Twin Cam® sprocket shafts. This tool is designed to install either H-D®...

Universal Tool Driver Spacer by JIMS®. The effectiveness of any bearing race remover tool is dependent on the ability to grip the race. This spacer applies outward force on the bearing race tool to grip better, allowing easier removal...

Cam Seal Installer and Remover Tool by JIMS®. Use to install and remove a 1970-1999 cam seal without removing the cam cover. This tool is very simple to use. Just mount tool in cover, screw in the two removing screws, turn center, and...

Motor Sprocket Shaft Seal Install Tool by JIMS®. Use to press oil seal over sprocket shaft into case. Use with No.97225-55. If you're looking for a quality product that will serve you for years to come, look no further.

Rear Seat Mounting Screw Tool by JIMS®. This tool is used on the Softail® seat mounting screw, H-D# 3075, to mount the seat to the rear fender. JIMS tool locates on the screw head to keep from scratching or damaging the rear fender or...

Starter Jackshaft Seal Installer Tool by JIMS®. This tool is designed to easily align and install the starter jackshaft seal (H-D® No.12066) without distorting or damaging the seal. This seal is located in the upper part of the inner...

Compensating Sprocket Lock Kit by JIMS®. Peace of mind is key when it comes to building a high performance powertrain. The Compensating Sprocket Lock Kit is now ready and available for select Harley-Davidson motorcycles. This system...

Pulley and Sprocket Mega Nut by JIMS®. JIMS now offers both early and late Mega Nuts. Once you install these left handed threaded nuts correctly they won't come loose with this exclusive lock plate design. They can also be used on BDL...

Sprocket Shaft Nuts by JIMS®. In an increasing demand for quality and durability with crank pin, sprocket and pinion shaft nuts, JIMS have been able to exceed JIMS own high standards by maintaining the pitch diameter perpendicular to...

Transmission Sprocket Spacer by JIMS®. Smooth finish for a longer seal life. Designed with precision and functionality in mind, this accessory ensures outstanding performance and easy use which makes it the perfect deal for your...

4-Speed Transmission Rebuild Kit by JIMS®. Use JIMS® proven transmission parts to start with, then top it off with a JIMS® Gasket set, together in one convenient package. This is a big time saver.

Countershaft Gear Bushing by JIMS®. Designed with precision and functionality in mind, this accessory ensures outstanding performance and easy use which makes it the perfect deal for your ultimate satisfaction.

Overdrive Transmission Rebuild Kit by JIMS®. JIMS® proven transmission parts to start with, then top it off with a JIMS® gasket set, together in one convenient package. This is a big time saver. If you're looking for a quality...

Shift Fork Shaft by JIMS®. Designed with precision and functionality in mind, this accessory ensures outstanding performance and easy use which makes it the perfect deal for your ultimate satisfaction.